Author Topic: Activation code TunerPro RT (Read 5747 times) racl. You mean registration code? You get that by making the $39 payment to Mark/Tuner Pro. Apr 25, 2018 - Tuner Pro RT allows reading real time data. That is what I've been using. So the following is for Tuner Pro RT I'm certainly. Place key in Run.

Posts: 1034 From: Easton, PA - USA Registered: Nov 2005 Feedback score: Report this Post 06:46 PM I'm having trouble getting TunerPro v5 to connect to my 7730 ECM. Phonedawgz, I followed all the directions in your 'Using tunerpro RT as a scanner setup' thread but am still having trouble. I'm using the Moates extreme ALDL USB cable. Easy ceiling polnaya versiya torrent.

Should it be on the 10k resistor or open setting? Either way, I go through and tunerpro says the cable is found and functioning. I'm running a modified $8f code from Ryan, so what definition file do I need? The $8F.ads file from tunerpro.net? Do I also need a.bin file?

And I don't need an.xdf file, correct? The problem is, I turn the key 'on' and hit connect and is just sits there trying to connect. It never says 'can't connect' it just always says 'DA: connecting.' I'm kind of just stuck here scratching my head.I don't know what I'm doing wrong. This seems like it should be pretty straightforward.

ETA: I read a couple other threads on forums about people having problems connecting specifically to 7730's but couldn't find any specific solutions. Anyone have trouble with this before? [This message has been edited by ConvictedRedneck (edited ).] IP: phonedawgz Member. Total ratings: 288 Report this Post 07:29 PM Moates extreme ALDL to USB cable - ick (just kidding) On my cables the 10k resistor is always there, so idk what you get without it.

I do know it works for me with the $88 and using the 10K Are you using TunerPro or TunerPro RT. TunerPro RT has a 15 second nag screen at the start of it and then it is fully functional, so even if you don't want to purchase TP RT it is suggested. Yes you need the $8f.ads file If using TP RT did you 'import' the ads? You should have had to and then TP RT would save it as an adx No you do not need the bin or xdf files IP: ConvictedRedneck Member. Posts: 1034 From: Easton, PA - USA Registered: Nov 2005 Feedback score: Report this Post 07:46 PM Tunerpro RT.

Yes, imported it as.ads (only one available for $8f) and then it prompted me to save it as an.adx which I did. With the 7730 conversion, there was only one wire at the aldl connector to move, correct? I'm thinking maybe this could be related to my problem I mentioned in my other thread where my fan comes on all the time with the key in the 'on' position, even without A-B jumpered. IP: ConvictedRedneck Member. Total ratings: 342 Report this Post 08:54 PM I'm having a similar problem.

I'm using a 7730 ECM with the $A1 code mask. I have TunerPro RT v5, and the A1 adx file. I have the serial port configured correctly (or at least, I think), and the ALDL cable (serial port version) is detected. But whenever I start data acquisition, I just get a constant stream of errors. I've tried it with the 10k resistor 'on' and 'off', with no change. And my data line is on pin M of the ALDL plug. IP: ConvictedRedneck Member.

Posts: 1034 From: Easton, PA - USA Registered: Nov 2005 Feedback score: Report this Post 09:12 PM Correct, data line moved to pin M. Blacktree, same situation except I don't get errors, it just sits there and doesn't do anything. At the bottom where it says 'Not emulating' and 'DA: Not connected' what else should/shouldn't it say when your plugged into ALDL with/without engine on? Mine says 'Hardware not found' all the time and 'Not ready' most of the time. Is moving Pin M at ALDL possibly the problem? IP: ConvictedRedneck Member.

Total ratings: 288 Report this Post 07:25 AM I can send you a test set up that I use with a known working USB cable, a known working 7730 with MEM.CAL and a known working test cable that plugs into the 7730, connects to 12v and has an ALDL cable. Then you should be able to make some sense of what does work and then also come up with what is not working with your set up. There will be a core charge for the stuff, but then return whatever you don't use and I will refund the core charge for whatever you don't use. IP: BowtieBob Member Posts: 18 From: Newbury.Park, CA.

Registered: Apr 2003 Feedback score: Report this Post 09:12 PM ConvictedRedneck, did you ever figure this one out? I am having the same problem with Tunerpro RT on both a 1988 2.8 V6 using the $24 ads file from tunerpro.net (imported to an adx) and also on a 1988 2.5 using the 87-88_2.5.adx file from phonedawgz (thanks phonedawgz!). I connected the cable with jumpers using bare pins on the ALDL to be sure there was electrical connection, but it's stuck at attempting to communicate just like you said in your initial post. Tunerpro does recognize the USB cable. I am using a OBD Diagnostics 12 pin USB/ALDL cable with the 10kOhm jumpered in (so phonedawgz please don't flame me).